Yes you might struggle to remove the screw without removing the frame, as
access is cramped. Unless cosmetics are important I'd look for a
replacement nut that can be screwed onto the front, although to fit, it may
need to be a special type as per the remaining one. Failing that, a suitable
glue might hold the door onto the frame on that side. Tim
----- Original Message -----
From: "Eli Bildirici" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Wednesday, November 15, 2017 2:13 AM
Subject: Re: [ARSCLIST] Tascam 122 MkII door and seek issues
Thanks all for chiming in.
I've removed the door window but the old screws are still in there:
and I'm not sure how to get them out.
I don't have much experience servicing electronics of this vintage. Is
replacing the idler tire (I only see one but haven't looked at the service
manual yet) a simple enough task with schematics that a relative newcomer
can do it? If not I'll look into servicing the deck. (Any recommended
technicians in and around Manhattan would be greatly appreciated.)
November 13 2017 5:41 PM, "Tim Gillett" <[log in to unmask]> wrote:
> The weak drive is probably caused by the rubber idler tyre(s) going hard
> with age and losing their
> grip. A technician can clean the tyre and even roughen up its surface with
> abrasive to try and get
> a bit more useful life out of it, but the real solution is normally
> replacing the tyre(s). I dont
> have a MarkII in my workshop at present but from memory the idler tyre(s)
> are different from the
> later MkIII model . I remember replacing the tyres on two MkII's at the
> start of a big digitising
> project in 2010.
> As Marie said, the clear door and frame should be able to be removed
> upwards. Again it's a
> different design to the MkIII model but I think you should be able to
> remove upwards the frame on
> which the clear plastic window is (now half) attached. Then you should be
> able to replace the
> missing screw and nut with an ordinary metal thread type. The fancy nut
> with the two small holes is
> just for appearance sake. I prefer to keep doors normally on machines to
> prevent dirt and dust
> entering the mechanism.
> ----- Original Message ----- From: "Marie O'Connell" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Tuesday, November 14, 2017 4:56 AM
> Subject: Re: [ARSCLIST] Tascam 122 MkII door and seek issues
>> It is only the front part of the door, not the whole door, and that part
>> should just lift off without much effort as there are no screws holding
>> Q-stick and isopropyl alcohol to gently clean the heads and rollers >
>> fiddley to do but essential to keep the path clean.
>> On Tue, Nov 14, 2017 at 9:14 AM, Eli Bildirici <
>> [log in to unmask]> wrote:
>>> How did you remove the door? I'm not sure how to deal with the remaining
>>> We have not attempted any kind of cleaning. I'm not sure what the proper
>>> procedure is, particularly for the rollers.
>>> November 13 2017 1:57 PM, "Marie O'Connell" <[log in to unmask]> wrote:
>>>> We have been in the practise of removing that front part of the door so
>>>> can get at the cassette if it stops in the machine.
>>>> I know this is probably a silly question for rewind, what you call
>>>> but have you cleaned the heads and rollers?
>>>> On Tue, Nov 14, 2017 at 5:55 AM, Eli Bildirici <
>>>> [log in to unmask]> wrote:
>>>>> Hey all,
>>>>> We use a Tascam 122 MkII for our cassette tape captures. Playback is
>>>>> >> >> OK
>>>>> far as I can tell, but we have two issues: the plastic door cover is
>>>>> missing one of the 'screws' - not actually a screw, or a nail, but I'm
>>>>> sure what to call it. A fastener??? Anyway - and seeking, in either
>>>>> direction, is extremely slow. If there is variance by tape, I have not
>>>>> noticed it. Over the past year I've captured at least fifty tapes with
>>>>> I haven't been able to find any information on what could serve as a
>>>>> substitute fastener for the door, and don't know if the seeking issue
>>>>> >> >> is
>>>>> fixable, or how to.
>>>>> I took videos of the issue and uploaded them to Youtube. Here's what
>>>>> happens on ejection (https://youtu.be/KVWxCBfTRqw), and here's an
>>>>> to rewind a tape (https://youtu.be/LzJQy1yjyFE).
>>>>> Thanks everyone for your time! Looking fwd, I hope, to some of the >>
>>>>> >> usual
>>>>> sage advice.
>>>>> Eli Bildirici
>>> Eli Bildirici
>>> (347) 837-8337
> This email has been checked for viruses by Avast antivirus software.