Print

Print


On 09/10/2012 18:36, James Roth wrote:
> PLEASE TELL ME
> How does one cancel the vertical portion of the signal?
>
> Regards,
> Ben Roth
>
> -----Original Message-----
> From: Association for Recorded Sound Discussion List [mailto:[log in to unmask]] On Behalf Of Steven Smolian
> Sent: Tuesday, October 09, 2012 1:22 PM
> To: [log in to unmask]
> Subject: Re: [ARSCLIST] What's the best way to remove surface noise on Columbia Shellac (1930)?
>
> Are people not cancelling the vertical portion of the signal?
>
> Steve Smolian
>
>
> -----Original Message-----
> From: Association for Recorded Sound Discussion List [mailto:[log in to unmask]] On Behalf Of Mickey Clark
> Sent: Tuesday, October 09, 2012 1:11 PM
> To: [log in to unmask]
> Subject: Re: [ARSCLIST] What's the best way to remove surface noise on Columbia Shellac (1930)?
>
> Try a slow transfer at 33 1/3 - at the slower speed, your cartridge will follow the irregularities - it should be all low frequency noise.
> -cheers-Mickey Follow me on Twitter https://twitter.com/MickeyRClark M.C.Productions Vintage Recordings
>      710 Westminster Ave. West
>               Penticton BC
>                  V2A 1K8
>
> ----- Original Message -----
> From: "James Roth" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Tuesday, October 09, 2012 9:07 AM
> Subject: Re: [ARSCLIST] What's the best way to remove surface noise on Columbia Shellac (1930)?
>
>
>> Hello alls also.
>>
>> I had the same question about 1/2 year ago.
>> I have hundreds of those woow-woow surface noise Columbias.
>> I've tried 10 different styli - truncated/full conical, eliptical, etc.
>> (Shure and Stanton) and the GE VRII cartridge with the 3 mil stylus.
>> ...but no luck.
>>
>> Regards,
>> Ben Roth
>>
>>
>> -----Original Message-----
>> From: Association for Recorded Sound Discussion List
>> [mailto:[log in to unmask]] On Behalf Of Raphaël PAREJO
>> Sent: Tuesday, October 09, 2012 11:01 AM
>> To: [log in to unmask]
>> Subject: [ARSCLIST] What's the best way to remove surface noise on
>> Columbia Shellac (1930)?
>>
>> Hello alls!
>>
>> I've a lot difficulties to resolve a problem of surface noise and
>> rumble on a Columbia shellac (circa 1930, electric recording) from San
>> Sebastian (Basque country) factory.
>>
>> What's the best ways to attenuate or remove this persistant noise ?
>>
>> I'm working on a Macintosh computer with Peak Pro 7 Editor and several
>> plugins as iZotope RX2, Oxford restoration suite, and also the
>> discontinued SoundSoap Pro 2. The results are not good.
>>
>> A colleague have tried to use Cedar 3000, but without good results.
>>
>> Some suggestions?
>>
>> regards.
>>
>> --
>> R. Parejo-Coudert
>>
>> Ethnomusicologue / Ethnomusicologist / Etnomusicólogo
>>
>> Anthropologie visuelle et sonore
>> Visual and Sound Anthropology
>> Antropología visual y sonora
>>
>> Archives sonores - Archivos sonoros - Sound Archives Restauration
>> audio - Restauración audio - Audio Restoration
>>
>>
>> °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°
>> °°
>>
Connect left and right channels of the pickup in parallel. The wanted 
modulation is in the lateral direction, and all you are likely to get in 
the vertical is pinch effect and rumble.