Print

Print


Just convert the .wav file to mono. The vertical will be eliminated-Mickey
Follow me on Twitter
https://twitter.com/MickeyRClark
M.C.Productions Vintage Recordings
    710 Westminster Ave. West
             Penticton BC
                V2A 1K8

----- Original Message ----- 
From: "Ted Kendall" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Tuesday, October 09, 2012 11:30 AM
Subject: Re: [ARSCLIST] What's the best way to remove surface noise on 
Columbia Shellac (1930)?


> On 09/10/2012 18:36, James Roth wrote:
>> PLEASE TELL ME
>> How does one cancel the vertical portion of the signal?
>>
>> Regards,
>> Ben Roth
>>
>> -----Original Message-----
>> From: Association for Recorded Sound Discussion List 
>> [mailto:[log in to unmask]] On Behalf Of Steven Smolian
>> Sent: Tuesday, October 09, 2012 1:22 PM
>> To: [log in to unmask]
>> Subject: Re: [ARSCLIST] What's the best way to remove surface noise on 
>> Columbia Shellac (1930)?
>>
>> Are people not cancelling the vertical portion of the signal?
>>
>> Steve Smolian
>>
>>
>> -----Original Message-----
>> From: Association for Recorded Sound Discussion List 
>> [mailto:[log in to unmask]] On Behalf Of Mickey Clark
>> Sent: Tuesday, October 09, 2012 1:11 PM
>> To: [log in to unmask]
>> Subject: Re: [ARSCLIST] What's the best way to remove surface noise on 
>> Columbia Shellac (1930)?
>>
>> Try a slow transfer at 33 1/3 - at the slower speed, your cartridge will 
>> follow the irregularities - it should be all low frequency noise.
>> -cheers-Mickey Follow me on Twitter https://twitter.com/MickeyRClark 
>> M.C.Productions Vintage Recordings
>>      710 Westminster Ave. West
>>               Penticton BC
>>                  V2A 1K8
>>
>> ----- Original Message -----
>> From: "James Roth" <[log in to unmask]>
>> To: <[log in to unmask]>
>> Sent: Tuesday, October 09, 2012 9:07 AM
>> Subject: Re: [ARSCLIST] What's the best way to remove surface noise on 
>> Columbia Shellac (1930)?
>>
>>
>>> Hello alls also.
>>>
>>> I had the same question about 1/2 year ago.
>>> I have hundreds of those woow-woow surface noise Columbias.
>>> I've tried 10 different styli - truncated/full conical, eliptical, etc.
>>> (Shure and Stanton) and the GE VRII cartridge with the 3 mil stylus.
>>> ...but no luck.
>>>
>>> Regards,
>>> Ben Roth
>>>
>>>
>>> -----Original Message-----
>>> From: Association for Recorded Sound Discussion List
>>> [mailto:[log in to unmask]] On Behalf Of Raphaël PAREJO
>>> Sent: Tuesday, October 09, 2012 11:01 AM
>>> To: [log in to unmask]
>>> Subject: [ARSCLIST] What's the best way to remove surface noise on
>>> Columbia Shellac (1930)?
>>>
>>> Hello alls!
>>>
>>> I've a lot difficulties to resolve a problem of surface noise and
>>> rumble on a Columbia shellac (circa 1930, electric recording) from San
>>> Sebastian (Basque country) factory.
>>>
>>> What's the best ways to attenuate or remove this persistant noise ?
>>>
>>> I'm working on a Macintosh computer with Peak Pro 7 Editor and several
>>> plugins as iZotope RX2, Oxford restoration suite, and also the
>>> discontinued SoundSoap Pro 2. The results are not good.
>>>
>>> A colleague have tried to use Cedar 3000, but without good results.
>>>
>>> Some suggestions?
>>>
>>> regards.
>>>
>>> --
>>> R. Parejo-Coudert
>>>
>>> Ethnomusicologue / Ethnomusicologist / Etnomusicólogo
>>>
>>> Anthropologie visuelle et sonore
>>> Visual and Sound Anthropology
>>> Antropología visual y sonora
>>>
>>> Archives sonores - Archivos sonoros - Sound Archives Restauration
>>> audio - Restauración audio - Audio Restoration
>>>
>>>
>>> °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°
>>> °°
>>>
> Connect left and right channels of the pickup in parallel. The wanted 
> modulation is in the lateral direction, and all you are likely to get in 
> the vertical is pinch effect and rumble.
>