Print

Print


Digitizing in stereo also allows decrackling and declipping of the groove walls independently then re-combining them to get back the hill and dale. 
I fix a lot of mono lateral recordings by converting to MS and treating the vertical and horizontally independently then recombining. Often the garbage in the vertical can be isolated and added back into the lateral out of polarity and it cleans up dramatically. 




> On May 5, 2015, at 5:58 PM, Mickey Clark <[log in to unmask]> wrote:
> 
> Hello Mr. Roth - all I meant is that you can have the cartridge phased normally i.e. when you play a modern stereo record, it will be correct. You don't need to physically re-wire your cartridge unless you intend to just listen to the music. When I'm recording, I have the volume low because I am more concerned with listening to the final product. When I said out of phase I meant out of phase for vertical records. I have one turtable I use for almost all recording and like to keep is simple - I still have about 100 diamond discs  - would you like a list? -Mickey
> 
> 
> 
> Follow me on Twitter
> https://twitter.com/MickeyRClark
> M.C.Productions Vintage Recordings
>   710 Westminster Ave. West
>            Penticton BC
>               V2A 1K8
>           1-250-462-7881
>   http://mcproductions.ca
> ----- Original Message ----- From: "James Roth" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Tuesday, May 05, 2015 10:19 AM
> Subject: Re: [ARSCLIST] Playing Edison Diamond discs
> 
> 
>> Greetings, Mr. Clark
>> 
>> Thank you for responding to my inquiry.
>> 
>> I'm not quite sure what you meant by "record in stereo (out of phase)".
>> Are you referring to the wiring of the cartridge for vertical grooves?
>> 
>> Also, "invert the phase of one channel" and combine for mono.
>> I use Sony Sound Forge 9 which has an "Invert/Flip" tool.
>> It turns the wave of that channel upside down.
>> Is that what I need to do?
>> Please explain a little further.
>> Thank you.
>> 
>> Ben Roth
>> 
>> 
>> 
>> 
>> -----Original Message-----
>> From: Association for Recorded Sound Discussion List [mailto:[log in to unmask]] On Behalf Of Mickey Clark
>> Sent: Tuesday, May 05, 2015 11:53 AM
>> To: [log in to unmask]
>> Subject: Re: [ARSCLIST] Playing Edison Diamond discs
>> 
>> If you're using a computer, you can record in stereo (out of phase) , then using a wave editor, invert the phase of one channel, then combine for mono.
>> I know the process - and the sound will be horrible until you combine the tracks for mono - then all the noices will miraculously disappear!!! I use the same cartridge for modern stereo and verticals - saves a lot of hassle to do it this way and you don't need a designated cartridge wired for verticals - Mickey Clark
>> 
>> 
>> Follow me on Twitter
>> https://twitter.com/MickeyRClark
>> M.C.Productions Vintage Recordings
>>   710 Westminster Ave. West
>>            Penticton BC
>>               V2A 1K8
>>           1-250-462-7881
>>   http://mcproductions.ca
>> ----- Original Message -----
>> From: "James Roth" <[log in to unmask]>
>> To: <[log in to unmask]>
>> Sent: Tuesday, May 05, 2015 7:58 AM
>> Subject: [ARSCLIST] Playing Edison Diamond discs
>> 
>> 
>>> Hello everyone,
>>> 
>>> I am transferring Edison Diamond disks.
>>> I'm using a Shure M44-7 with a 3.5 FCR stylus from Expert Stylus.
>>> I think I've rewired the leads properly for a hill-n-dale groove.
>>> The turntable is a Technics Quartz SL 1200 Mk 2.
>>> I'm using a KAB Great Sound Escort pre-amp.
>>> Still, the sound leaves much to be desired.
>>> 
>>> I'm having an extra hard time transferring the Liszt 2nd Hungarian
>>> Rhapsody p/b Rachmaninoff.
>>> Any suggestions?
>>> 
>>> Thank you.
>>> Ben Roth
>>> 
>>> P.S. I strongly dislike that cadenza of Rachmaninoff!  I don't think Liszt
>>> would have like it either.
>>> 
>> 
>> 
>> ---
>> This email has been checked for viruses by Avast antivirus software.
>> http://www.avast.com
> 
> 
> ---
> This email has been checked for viruses by Avast antivirus software.
> http://www.avast.com